Tab Sensitivity ControlĚdjusts for density in tab/wafer sealsĬounterĕ Digit LCD (Operator Resettable)įeeder Integrated Bottom Feed for Continuous OperationĭimensionsĒ5″ Wide x 15. Tab Size Length: 5/8″ to 1-1/4″ (Standard Tabs) T-750 Tabber & Stamp Affixer OPERATIONS MANUAL Revised: 3-4-08 Part M-3436 RENA SYSTEMS INC. Speedđ2,000 pieces per hour (8.5″ tri-folds) Tab Sensitivity Control Adjusts for Density in Tab/Wafer Seals Tabbing Machine Specifications Integrated Bottom Feed for Continuous Operation Remember, folded mailers won’t qualify for USPS automation discounts without tabs. The RENA Systems T-250 Single Tabber will improve the effectiveness of your mailings while keeping down costs. It’s easy to set up and easy to operate for a continuous and reliable performance. Tab size can be 5/8” to 1-1/4” (standard tabs). The versatile T-250 handles a variety of material sizes and pieces up to 5/32’’ thick. It can handle flyers, programs, announcements, calendars and any other pieces that need to be sealed with a simple tab, up to 12,000 pieces per hour. New feed roller material works better longer. With the RENA Systems T-250, you get the advantages and cost savings of high-speed tabbing in one compact unit. Every tab is a tight secure seal, to meet all US postal requirements. The T-250 takes paper, translucent or clear tabs. The newly designed RENA Systems T-250 is a perfect companion to our tabletop Envelope Imager series of inkjet addressing systems. THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY.Rena T-250 Single Head Tabbing Machine Retail Price: $6,000.00 Tabbing Machine Descriptionīusiness is growing and you’re ready to add timesaving tabbing technology to your mailing operations. GETTING ACQUAINTED Section 1 – Getting Acquainted Safety Precautions SECTION 5 – MAINTENANCE _ 20Ĭ LEANING _ 20įeed Rollers and Forwarding Rollers_ 20 Cleaning the Sensors _ 21ĪPPENDIX - SPECIFICATIONS _ 23ĪPPENDIX B – OBTAINING SUPPLIES, SERVICE AND SUPPORT_ 24 T-250 T AB S UPPLIES: _ 24 T ABBING P ROBLEMS : _ 17 M EDIA F EEDING P ROBLEMS :_ 18 LOADING TABS : _ 11 TAB SENSITIVITY ADJUSTMENT _ 12 METERING BRACKET /SEPARATOR ADJUSTMENT _ 13 MEDIA SUPPORTS AND MEDIA SIDE GUIDE ADJUSTMENT _ 14 MEDIA TRANSPORT TEST _ 14 HORIZONTAL TAB POSITIONING _ 15 TAB FOLD POSITION ADJUSTMENT _ 15 OPERATING SEQUENCE _ 15 SECTION 2 – ASSEMBLY AND INSTALLATION _ 9Ī SSEMBLY_ 9 I NSTALLATION _ 10 S AFETY P RECAUTIONS _ 5 P ACKAGING /S HIPPING _ 6 C ONTENTS_ 6 F RONT V IEW _ 7 R EAR V IEW _ 8 Metering Bracket/Separator Adjustement, 13.All the tab rolls, shown above, are on a 3” core.Appendix B – Obtaining Supplies, Service and Support.Specifications subject to change without notice.Top load, bottom feed for continuous operation.Avoid using solvents on the rubber rollers.DO NOT USE SOLVENTS TO CLEAN THE RUBBER ROLLERS.Separator Fingers or Feed Rollers worn.Metering Bracket/Separators not set evenly.Media not properly fanned before loading.Tab Drive Pressure knob in OFF position.To Stop the Tabber press the Feed Switch again.Activate the Tab Switch (switch will illuminate).Loosen the Tab Fold Position Adjustment Knob.Once the Media is feeding satisfactory, go to the next step. Media Supports and Media Side Guide Adjustment.Replace the Exit Roller by pushing it back into its holder.Step 3: Adjust the Metering Bracket Assembly to the media.Step 2: Set the sensitivity of the Tab Sensor.
0 Comments
Leave a Reply. |